NXTPLAST Ready Mix Plaster is a ready mix cement plaster with high quality polymer additives to sub-stitute for the traditional site mix wall plaster process. The solutionconsists ofprocessed sand which is graded and distributed as per particle size and proportionately mixed, cement and water soluble polymers which act as additives. The application method requires mixing of water before application and the mix is ready for plastering NXTPLAST Ready Mix Plaster can be used for both external and internal plastering
NXTPLAST Ready Mix Plaster can be applied on:
• AAC Block Walls • Clay Brick Walls
• Fly Ash Block Walls • Stone Walls
• Concrete Block Walls • Concrete Surfaces
NXTPLAST Ready Mix Plaster is a ready mix cement plaster with high quality polymer additives to sub-stitute for the traditional site mix wall plaster process. The solutionconsists ofprocessed sand which is graded and distributed as per particle size and proportionately mixed, cement and water soluble polymers which act as additives. The application method requires mixing of water before application and the mix is ready for plastering NXTPLAST Ready Mix Plaster can be used for both external and internal plastering
NXTPLAST Ready Mix Plaster can be applied on:
• AAC Block Walls • Clay Brick Walls
• Fly Ash Block Walls • Stone Walls
• Concrete Block Walls • Concrete Surfaces
FEATURES & BENEFITS
High Strength
High compressive and tensile strength increases masonry strength and load-bearing capacity.
Availability
Unlike the uncertain availability of raw river sand, premix bags are available round the year.
Higher Coverage
Due to lower density and high volume, it covers 15-20 sq.ft./bag with athickness of 10-12mm.
Consitency
Due to the manufacturing process and accurate particle size distribution, the premix bags are of consistent quality.
Economical
It provides smooth finish walls even in a single coat. Hence saves time and cost required for putty coating.
Minimum Cracks
Shrinkage cracks are minimised as premix plaster raw materials are tested and accurately mixed with specific particle size and quantity.
Premixed
No site mix and blending of powder is required. Only wateris to be added.
Finish
Surface finish after application is excellent and equal due to best particle size grading, hence maximizing wall plaster performance.
Easy Application
The material is pre-mixed and only water has to be added on site. This makes the process of plastering much easier and quicker.
Minimum Wastage
The wastage caused in the conventional site mix process while sand sieving and mixing material is totally avoided.
Storage
Easy to maintain stock as equal size packaging in bag form is provided.
TECHNICAL SPECIFICATION
FEATURES & BENEFITS
- This product is non-toxic and non-hazardous.
- Use of gloves, dust mask and goggles is recommended.
- In case of contact with skin/eyes, wash with plenty of clean water.
- In situations of prolonged irritation, professional medical aid should be sought.
“The information provided in this document results from our knowledge of the products and our experience. On-site results may vary, in particular, according to the product application methods adopted. Where application methods not covered by this document are used, customers must request speci?c additional information and/or carry out a representative test before using the products. The above-mentioned information in no way constitutes a warranty relative to the use of the products. Our general terms and conditions of sale shall prevail, in any event, on the information provided in this document. Prior to application, customers and users are requested to check that they have the latest version of this document.”
PREPARATION AND APPICATION
Concrete Block Joints
All concrete and block joints must be covered with a chicken wire mesh.
Mix Preparation
In 6-7 liters of potable water add 1 bag ot NXTPLAST Ready Mix Plaster.
Remixing
Re-mixing should be done for 5-10 minutes.
Leveling
Atter final coat ensure proper levelnq with the help of appropriate tools.
Surface Clean
The surface should be free from oil, grease, paint, loose plaster or dirt particles.
Leave to React
Leave the mix to react for 5-10 min and remix before use.
Apply on Wall
The mixture should be thrown while the cement slurry is wet, ensure levelling with the help of tools.
Water Curing
In-normal weather, NXTPLAST doesn’t need water curing for the first 24 hours. After the plaster is completely dry, curing should be done 2-3 times for 2-3 days. In abnormal weather conditions, curing for 5-7 days is required.
Wall Wetting
Dampen the wall before application of plaster.
Cement Slurry
Apply cement slurry, If tho surface is smooth and dence, the surface should be made rough.
Second Coat
If 2nd coat is required, ensure grooving on first coat to provide good grip for 2nd coat.
KNOWLEDGE BASE